Pool tables are designed for patios and indoor sports arenas. Pool is a game that most play during their leisure time with family and friends. The tables are able to last as long as 20 years with minimal maintenance when they are made from durable material. The part of the structure that is most vulnerable is the felt. In considering pool table refelting Denver residents should know the steps taken in order to come up with excellent results.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
After the choice of color, the rails need to be removed using a crescent wrench. This is done by removing the bolts that attach the rails. Rails are also always covered by the felt and need to be re-felted too. This explains the need to buy extra material. Rails are carefully placed on the floor close to the table so that there is no mistake when reattaching them.
A staple remover is used when removing the old material. It is used to out staples which are at the felt edges. All felt should be removed from the table so that the newly placed one is perfectly fitted. The one that has been removed can be put in a thrash bag to be disposed later.
The new felt should be placed carefully while making sure to inspect that there are no any damages or stains on it. It should then be cut using a sharp scissor while using the border of the table top as the guide. There needs to be some felt that is left over that will be used for re-felting the rails.
After making the cut, there is attachment of the felt to the table top using staplers. When stapling, you should start from the mid-point of one of the ends before proceeding to the left and right edges. Thereafter, you proceed to the opposite end and pull the felt tightly. This is followed by stapling it as was the case in the other side.
Side edges are then stapled. It is essential to ascertain that the staples are placed at the same distance from each other. They also need to be lined up in the correct way. 3 slits are cut on each pocket then the felt is wrapped and stapled on the pocket edges. Before stapling, the felt is tightly pulled.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
The felt is the fabric which is attached to the surface of the table. When re-felting, the first step is to determine the size of the pool table using a measure tape. The felt is then replaced at a sports shop or home improvement depot. The material should be purchased such that there is an extra 12 inches to the width and length. Because there are many colors, it will be important to decide if the same color as the one being replaced will be used or a different one.
After the choice of color, the rails need to be removed using a crescent wrench. This is done by removing the bolts that attach the rails. Rails are also always covered by the felt and need to be re-felted too. This explains the need to buy extra material. Rails are carefully placed on the floor close to the table so that there is no mistake when reattaching them.
A staple remover is used when removing the old material. It is used to out staples which are at the felt edges. All felt should be removed from the table so that the newly placed one is perfectly fitted. The one that has been removed can be put in a thrash bag to be disposed later.
The new felt should be placed carefully while making sure to inspect that there are no any damages or stains on it. It should then be cut using a sharp scissor while using the border of the table top as the guide. There needs to be some felt that is left over that will be used for re-felting the rails.
After making the cut, there is attachment of the felt to the table top using staplers. When stapling, you should start from the mid-point of one of the ends before proceeding to the left and right edges. Thereafter, you proceed to the opposite end and pull the felt tightly. This is followed by stapling it as was the case in the other side.
Side edges are then stapled. It is essential to ascertain that the staples are placed at the same distance from each other. They also need to be lined up in the correct way. 3 slits are cut on each pocket then the felt is wrapped and stapled on the pocket edges. Before stapling, the felt is tightly pulled.
The last step is to reassemble the structure. The rails are attached to their proper position using the crescent wrench. After insertion of the pocket lines, the re-felted table can be used.
ليست هناك تعليقات:
إرسال تعليق